Finncoatings® Color on the highest level

 

TEMAFLOOR 3000

 

 

CE logo

Materialbasis     Fin   Finncoatings®color on the highest levelncoatings®color on the highest level

Lösemittelfreie TEMAFLOOR 3000 Epoxidbodenbeschichtungsmasse wird aus TEMAFLOOR P300 Epoxidbeschichtungsstoffmischung und Sand vorbereitet.

ANWENDUNGSGEBIETE UND EIGENSCHAFTEN

 

Alte und neue Betonfussböden in Industrieräumen, Lagerhäusern und Reparaturwerkstätten die starker chemischer und mechanischer Belastung ausgesetzt sind, z.B. Produktions- und Papiermaschinenhallen, Gabelstaplerfahrwege, sowie
sonstige Fussböden unter hoher Punktbelastung.Hohe abriebfestigkeit.Beständig gegen Wasser, Öl, Fett, Chemikalien und schwache Lösungen von nichtoxydierenden Säuren, Alkali und Salzlösungen; Oxydierende Säuren und Bleichlaugen nur als vereinzelte Spritzer. Genauere Angaben über Chemikalienbeständigkeit in gesonderter Tabelle. Beständig gegen bis zu +70ºC trockene Hitze und bis zu +60ºC bei Unterwasserbelastung. Nicht beständig gegen grosse, häufig auftretende plötzliche Temperaturänderungen.Selbstglättende Masse. Geeignet für Fussböden mit einer Gefälle von maximal 5%. TEMAFLOOR FLEX hardener macht die Obefläche des Anstriches elastich und mehr
dauerhaft gegen Wandern order Betonbruch und verbessert die Stossfestigkeit.

Farbtöne

RAL, NCS, SSG, BS, MONICOLOR NOVA and SYMPHONY colour cards. TEMASPEED tinting.


Glanzgrad
       Finncoatings®color on the highest level

Hochglanz
 
Mix the correct proportions of base and hardener thoroughly (approx. 2 minutes) by using a hand drill with a paddle. Add filler to the mixture mixing carefully at the same time. Use dry, clean natural or quarz sand as a filler. Wet sand will result in air bubbles and decreased gloss in the finished screed. The amount of mixture depends on the area to be coated and on the pot life of the mixture. Insufficient mixing or incorrect mixing ratio will result in uneven drying of the surface, weaken the properties of the screed and risk the success of the application.


Cleaning of tools
   

Thinner 006 1029 or Thinner 006 1031.


EU VOC 2004/42/EC-limit value     VOC 2004/42/EC (cat A/j) 500 g/l (2010)
Temafloor 3000: max. VOC < 500 g/l

 

The European harmonized productstandard EN 13813 defines the requirements for Screed materials and floor screeds, including synthetic resin screeds.This product is tested and CE-labelled in accordance with the tables ZA.1.5 and ZA.3.3 in the appendix ZA.3.

 

CE logo
 
Tikkurila Oyj
Kuninkaalantie 1
FI-01301 VANTAA
11
TIK 8400-5011b
EN 13813
Coating/Screed
Abrasion resistance
RWA 1
Chemical resistance
CR 1, 2, 4, 5, 6, 6b, 7, 8, 11, 12, 14 (Class 2)
   
Release of corrosive substances
SR
Impact resistance
IR4
Sound insulation
NPD
Sound absorption
NPD
Thermal resistance
NPD
Reaction to fire
Bfl
Water permeability
NPD
Adhesion
Adhesion strength by pull off test: B 2.0
 

 

 

The European harmonized productstandard EN 1504-2 defines the requirements for surface protection systems for concrete.This product is tested and CE-labelled in accordance with the tables 1d, 1f and 1g in the
appendix ZA.

 

 

 

CE logo
0809

 

    Finncoatings®color on the highest level

 

Tikkurila Oyj
Kuninkaalantie 1
FI-01301 VANTAA
13
TIK 8400-5011a
EN 1504-2
Coating
Abrasion resistance
< 3000 mg
Resistance to severe chemical attack
Class II
   
Permeability to CO2
CO2sD > 50 m
Impact resistance
Class I: ≥ 4 Nm
Permeability to water vapour
Class II, 5 m < sD < 50 m
Capillary absorption and permeability to water
w < 0,1 kg/m² ∙ h0,5
Adhesion
Adhesion strength by pull off test: ≥ 2,0 N/mm²
Reaction to fire
Bfl-s1

 

The above information is not intended to be exhaustive or complete. The information is based on laboratory tests and practical experience, and it is given to the best of our knowledge. The quality of the product is ensured by our operational system, based on the requirements of ISO 9001 and ISO 14001. As manufacturer we cannot control the conditions under which the product is being used or the many factors that have an effect on the use and application of the product. We disclaim liability for any damages caused by using the product against our instructions or for inappropriate purposes. We reserve the right to change the given information unilaterally without notice. The product is intended for professional use only and shall only be used by professionals who have sufficient knowledge and expertise on the proper use of the product. The information above is advisory only. To the extent permitted by applicable law, we shall not approve of any liability for the conditions under which the product is being used or for the use or application of the product. In case you intend to use the product for any other purpose than that recommended in this document without first getting our written confirmation on the suitability for the intended use, such use takes place at your own risk.

 

Finncoatings® Color on the highest level

 

 

Finncoatings  
Heidelberger Straße 8
74858 Aglasterhausen-Germany

 

Tel. + 49 (0)6262 917095
Fax  + 49 (0)6262 917791

www.finncoatings.com
Mail. Diese E-Mail-Adresse ist vor Spambots geschützt! Zur Anzeige muss JavaScript eingeschaltet sein!