Finncoatings® Color on the highest level
Furniture Paint Deckender Holzlack
Wasserbasierter Acrylat-Latex Decklack. Geruchsarm, vergilbungsfrei für Hochwertige Innenlackierungen
Für Lackierarbeiten von Türen,Möbel Innenbereiche von Fenstern,Innenwänden und Decken, Putz, Beton,Gips, Span- und Holzfaserplatten.
Tikkurila Symphony 2436 Colour card,Finncoatings,RAL;NCS oder nach Kunden Wunsch.
8-10 m2/l je Anstrich
The above should be used as a guide, as actual spreading rates will depend upon many factors including texture, porosity and application method.
Can sizes 0,9 l, 2,7 l
Synthetic fiber brush, mohair roller.
Drying time at 23°C and 50% relative air humidity Touch-dry in one hour and recoatable after 16 hours. Ready to use hardness will be achieved after 2-3 days.
Wash resistance Resists over 5000 scrubbings by brush, SFS 3755
Chemical resistance Resists cleaning detergents and weak solvents e.g. White Spirit.Coffee, tea etc. stains have to be cleaned off immediately.
Light resistance Non-yellowing
Solids volume Approx. 40%
Density Approx. 1.2 kg/l in white (ISO 2811)
Storage Protect from frost.
The surface to be painted must be dry, the temperature of the air at least +8 C, and the relative humidity of the air below 80%.
Lower temperature (approx. +15 C) and higher humidity (50-70 % RH) will make the open-time of the paint longer and the work easier
Priming Unpainted surfaces:
Remove all dirt and dust carefully to obtain good adhesion. Treat knots with Oksalakka Knotting Lacquer. Prime new wood and wood fibre board surfaces with Feelings Furniture Primer or Otex adhesion primer. Prime metal surfaces with Rostex Super Akva or Rostex Super metal primer. Prime absorbent surfaces first with a primer thinned with 5-10%, and sand. Prime surface after that with an unthinned primer.
Previously painted surfaces:
Wash down previously painted surfaces with Maalipesu Cleaning Agent and rinse carefully with water. Remove loose, flaking paint with a scraper and sand hard, glossy and industrially painted surfaces matt. Remove sanding dust. Fill holes and cracks with Presto Furniture Putty or Rapid Filler and sand the filled parts. Prime with Feelings Furniture Primer or Otex adhesion primer, metal surfaces with Rostex Super Akva or Rostex Super metal primer.
Painting Stir Feelings Furniture Paint well before use and thin with water, if necessary. Apply by brush, roller, paint pad, or spray 1-2 times. Apply on large surfaces with e.g. a mohair roller and level with a brush. Multi-branched synthetic brushes are best suited for the work.
Cleaning of tools Remove excess paint from tools. Clean tools with water. Tikkurila Pensselipesu (Tool Cleaner) is recommended to be used to remove a bit hardened paint.
Cleaning earliest approx. 1 month after painting: The surfaces are cleaned with a soft brush, sponge or cleaning cloth and neutral (pH 6-8) dish washing solution. Clean very dirty surfaces with weakly alkaline (pH 8-10) washing detergent and e.g. cleaning cloth or sponge. Rinse the surface carefully.
The product achieves its final hardness and durability after one month under normal conditions, therefore the surfaces must be handled with care during a couple of weeks. If the surfaces need to be cleaned soon after finishing, clean them lightly with a soft brush or damp cleaning cloth.
Maintenance treatment If the surface was previously painted with Feelings Furniture Paint, then maintenance painting can be carried out without priming. See Pretreatment.
Note! If alkyd primer is used as a primer, the final adhesion into the primer is achieved after 2 weeks from the finishing painting. During this time avoid e.g. the usage of masking tape.
EU VOC 2004/42/EC-limit value (cat A/d) 130g/l(2010) Feelings Furniture Paint contains VOC max. 130g/l.
HEALTH AND SAFETY CLASSIFICATION The product is not classified as dangerous. A Safety Data Sheet is available on request. Safety Data Sheet - Feelings Furniture Paint
ENVIRONMENTAL PROTECTION AND WASTE DISPOSAL Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations.
TRANSPORT VAK/ADR -
Finncoatings® Color on the highest level
Heidelberger Straße 8
Tel. + 49 (0)6262 917095
Fax + 49 (0)6262 917791